A slotted lotus shaped microstrip antenna based an EBG structure

The objective of this paper is to study intensively the design of a printed slotted patch based lotus shape structure mounted on a dielectric substrate backed with an electromagnetic band Gap (EBG) layer for wideband applications. The dielectric substrate is made of a Roger RT/duroid®5880 layer. An EBG layer is introduced on the back profile of the substrate to provide a high gain bandwidth product over wide frequency bands. The antenna is fed with a novel coplanar waveguide (CPW) structure of a flared geometry; therefore, the ground plane is mounted on the same substrate surface with the patch structure. A conductive trace is introduced at the substrate back from the bottom connected to the CPW through two shoring plates to remove the effects of the EBG layer on the feed structure. The EBG performance and the antenna design methodology are discussed using analytical analyses and numerical parametric studies, respectively. The numerical simulation is conducted using CST MWS Finally; the optimal antenna design is fabricated and measured for validation to be compared to the simulated results

A Miniaturized Printed Circuit CRLH Antenna-based Hilbert Metamaterial Array

With the development of communication systems and antennas, various challenges arise that require antennas of small size with enhanced performance. Metamaterials (MTM) defects introduced a considerable solution to such a challenge. Therefore, in this paper, a lightweight with low profile antenna is designed based on a novel design of a Composite Right/Left-Handed CRLH-MTM Hilbert array. The proposed CRLH-MTM unit cell consists of a T-symmetric CRLH unit cell conjugated to the 3rd-order Hilbert on the ground plane through a T-stub structure to enhance the gain-bandwidth product. CST-MWS is used to stimulate and design the proposed antenna structure. The antenna parameters are optimized to evaluate the antenna performance in gain and S11. As a result, the antenna can operate forward and backwards with a large scanning angle ranging from +34o to -134o with changing frequency, and dual-band extended from 3.3GHz to 4.2GHz 4.86GHz 5.98GHz with a maximum gain of 7.24dBi and 3.74dBi, respectively. The beam steering is achieved by trough controlling the switching operation of PIN diodes. As a result, the antenna can scan up to 8° from 34° to 42° at 3.5GHz with constant gain along with the operating range

Design and analysis of a novel concentric rings based crossed lines single negative metamaterial structure

AbstractThis paper presents the design and analysis of a novel single negative metamaterial (MTM) based on concentric rings with crossed lines (CR-CL) to be miniaturized to λ/4 at 15GHz. The unit cell is structured to behave as a single negative MTM, -ε or -μ, at different frequency bands. The unit cell is consistent of a dielectric substrate, 5×5×1mm3, of FR4-Epoxy underneath of a conductive patch designed as 4.4×4.4mm2. A complete analysis in terms of S-parameters, constitutive parameters and refraction index are evaluated for the unit cell using both full wave simulation and circuitry analysis as well. Nevertheless, the unit cell characteristics based circuit equivalent lumped components are retrieved. HFSS software package based on Finite Element Method (FEM) and Advanced Design System (ADS) based on circuit analysis formulations are invoked to perform the simulation study. Later on, the obtained simulation results are compared to their identical measurements based on transmission line technique. Finally, the simulated and measured results are agreed excellently

Metasurface Antenna Circuitry for 5G Communication Networks

In this article, the proposed antenna structure is designed for modern wireless communication systems. The antenna structure is consistent of twelve-unit metasurface (MTS) unit cells. Therefore, the antenna size is miniaturized effectively to 30×35mm2 which is equivalently about 0.2λo, where λo is the free space wavelength at 3.5GHz. This is achieved by conducting the use of Hilbert shape MTS structure with T-resonator induction structure. The antenna structure is printed on a single side substrate to cover the frequency bands from 3.15GHz-3.63GHz and 4.8GHz-5.1GHz. Such antenna is found to provide a maximum gain of 3.5dBi and 4.8dBi at 3.5GHz and 5Ghz, respectively. Next, proposed antenna is found to be circularly polarized at 3.5GHz and 5GHz. The proposed antenna performance is simulated numerically using CST MWS software package with all design methodology that is chosen to arrive to the optimal performance. Then, the optimal antenna design is tested numerically using HFSS software package for validation. Finally, an excellent agreement is achieved between the two conducted software results

A Systematic Analysis and Design of a High Gain Microstrip Antenna based on a Single EBG Layer

In this paper, an Electromagnetic Band Gap (EBG) lens of a single layer is invented to improve the gain of a truncated slotted square patch antenna for the Wi-Fi applications. The proposed EBG lens is structured from 55 planar array. The individual unit cell is basically shaped as a couple of a split concave conductive patch. The proposed EBG struc- ture performance is tested numerically using Finite Integration Technique (FIT) formulations of CSTMWS and analytically using circuit theory. Then, the antenna performance in terms of |S11|, the boresight gain, and radiation patterns are reported and compared to the performance before introducing the EBG lens to identify the significant enhancements. The proposed EBG antenna is simulated numerically inside FIT formulations of CSTMWS time domain (TD) solver. A significant gain enhancement of 11.1 dBi at 2.45 GHz and a front to back ratio (F/B) about 22 dB are achieved after introducing the EBG lens. The antenna performance is validated using a frequency domain (FD) solver based CSTMWS formulations to obtain excellent agreements between the two invoked methods

A FRACTAL MINKOWSKI DESIGN FOR MICROWAVE SENSING APPLICATIONS

This work describes a low-cost, extremely sensitive microwave sensor that may be used to distinguish between different liquid samples by measuring the variation in S21 magnitude. An interdigital capacitor (IDC) in series with a circular spiral inductor (CSI) and linked directly to a light dependent resistor (LDR) is used to do this and been installed minkowski farctal on end both stub. The suggested sensor operates at a frequency of 1.47 GHz. Using Computer Simulation Technology (CST) Microwave studio, the impacts of modifying the proposed LDR's value are evaluated parametrically. However, When the LDR value changes in relation to the light of incidence, a considerable change in the resonance band is observed. Many recent wireless technologies that use optical-based interface systems have found that such technology is an excellent candidate. The same model is developed for validation using a High-Frequency Simulator Structure (HFSS). The suggested sensor is built on an FR4 substrate with a 40×60 mm2 surface area. As a ground plane, a copper layer is applied to the rear panel. The results obtained by the two software systems are in perfect agreement

An innovative fractal monopole MIMO antenna for modern 5G applications

Proposed in this paper is the design of an innovative and compact antenna array which based on four radiating elements for multi-input multi-output (MIMO) antenna applications used in 5G communication systems. The radiating elements are fractal curves excited using an open-circuited feedline through a coplanar waveguide (CPW). The feedline is electromagnetically coupled to the inside edge of the radiating element. The array's impedance bandwidth is enhanced by inserting a ground structure composed of low-high-low impedance between the radiating elements. The low-impedance section of the ground is a staircase structure that is inclined at an angle to follow the input feedline. This inter-radiating element essentially suppresses near-field radiation between adjacent radiators. A band reject filter based on a composite right/left hand (CRLH) structure is mounted at the back side of the antenna array to reduce mutual coupling between the antenna elements by choking surface wave propagations that can otherwise degrade the radiation performance of the array antenna. The CRLH structure is based on the Hilbert fractal geometry, and it was designed to act like a stop band filter over the desired frequency bands. The proposed antenna array was fabricated and tested. It covers the frequency bands in the range from 2 to 3 GHz, 3.4-3.9 GHz, and 4.4-5.2 GHz. The array has a maximum gain of 6. 2dBi at 3.8 GHz and coupling isolation better than 20 dB. The envelope correlation coefficient of the antenna array is within the acceptable limit. There is good agreement between the simulated and measured results.Dr. Mohammad Alibakhshikenari acknowledges support from the CONEX-Plus programme funded by Universidad Carlos III de Madrid and the European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No. 801538. Funding for APC: Universidad Carlos III de Madrid (Read & Publish Agreement CRUE-CSIC 2022)

Optical-Microwave Sensor for Real-Time Measurement of Water Contamination in Oil Derivatives

This paper presents a novel microwave sensor using optical activation for measuring in real-time the water contamination in crude oil or its derivatives. The sensor is constructed from an end-coupled microstrip resonator that is interconnected to two pairs of identical fractal structures based on Moore curves. Electromagnetic (EM) interaction between the fractal curves is mitigated using a T-shaped microstrip-stub to enhance the performance of the sensor. The gap in one pair of fractal curves is loaded with light dependent resistors (LDR) and the other pair with microwave chip capacitors. The chip capacitors were used to increase the EM coupling between the fractal gaps to realize a high Q-factor resonator that determines the sensitivity of the sensor. Empirical results presented here show that the insertion-loss of the sensor is affected by the change in LDR impedance when illuminated by light. This property is used to determine the amount of water contaminated oil. The sensitivity of the sensor was optimized using commercial 3D EM solver. The measurements were made by placing a 30 mm diameter petri dish holding the sample on top of the sensor. The petri dish was filled up to a height of 10 mm with the sample of water contaminated crude oil, and the measurements were done in the range between 0.76 GHz to 1.2 GHz. The Q-factor of the oil sample with no water contamination was 70 and the Q-factor declined to 20 for 100% contamination. The error in the measurements was less than 0.024%. The sensor has dimensions of 0.1270×0.1270×0.0040 and represents a new modality. Compared to existing techniques, the proposed sensor is simple to use, readily portable and is more sensitive

Photonic controlled metasurface for intelligent antenna beam steering applications including 6G mobile communication systems

This paper presents a novel metasurface antenna whose radiation characteristics can be remotely controlled by optical means using PIN photodiodes. The proposed reconfigurable antenna is implemented using a single radiating element to minimize the size and complexity. The antenna is shown to exhibit a large impedance bandwidth and is capable of radiating energy in a specified direction. The proposed antenna consists of a standard rectangular patch on which is embedded an H-tree shaped fractal slot of order 3. The fractal slot is used to effectively reduce the physical size of the patch by 75 % and to enhance its impedance bandwidth. A metasurface layer is strategically placed above the patch radiator with a narrow air gap between the two. The metasurface layer is a lattice pattern of square framed rhombus ring shaped unit-cells that are interconnected by PIN photodiodes. The metasurface layer essentially acts like a superstrate when exposed to RF/microwave radiation. Placed below the patch antenna is a conductive layer that acts like a reflector to enhance the front-toback ratio by blocking radiation from the backside of the patch radiator. The patch’s main beam can be precisely controlled by photonically illuminating the metasurface layer. The antenna’s performance was modelled and analyzed with a commercial 3D electromagnetic solver. The antenna was fabricated on a standard dielectric substrate FR4 and has dimensions of 0.778λo × 0.778λo × 0.25λo mm3 , where λo is the wavelength of free space centered at 1.35 GHz. Measured results confirm the antenna’s performance. The antenna exhibits a wide fractional band of 55.5 % from 0.978 to 1.73 GHz for reflection-coefficient (S11) better than − 10 dB. It has a maximum gain of 9 dBi at 1.35 GHz with a maximum front-to-back ratio (F/B) of 21 dBi. The main beam can be steered in the elevation plane from − 24◦ to +24◦. The advantage of the proposed antenna is it does not require any mechanical movements or complicated electronic systems.Dr. Mohammad Alibakhshikenari acknowledges support from the CONEX-Plus programme funded by Universidad Carlos III de Madrid and the European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No. 801538. The authors also sincerely appreciate funding from Researchers Supporting Project number (RSP2023R58), King Saud University, Riyadh, Saudi Arabia. Additionally, this work was supported by Ministerio de Ciencia, Innovación y Universidades, Gobierno de España (Agencia Estatal de Investigación, Fondo Europeo de Desarrollo Regional -FEDER-, European Union) under the research grant PID2021-127409OB-C31 CONDOR. Besides above, the Article Processing Charge (APC) was afforded by Universidad Carlos III de Madrid (Read & Publish Agreement CRUE-CSIC 2023)